Make Usb Bootable For Mac

by
Make Usb Bootable For Mac 9,0/10 3710 votes

Dec 18, 2018 - You don't need a bootable installer to install macOS, but it can be. After downloading the installer, connect the USB flash drive or other. If your Mac is using macOS Sierra or earlier, include the --applicationpath argument.

To troubleshoot an issue with Windows 10 (especially boot-related issues), it can be handy to boot to Windows 10 that is not installed on a Boot Camp partition. It is relatively straightforward to create a bootable USB Flash drive to boot to the Windows 10 installer, and then open up a DOS prompt for troubleshooting. What is needed • USB Flash drive (8 GB or larger recommended) • Windows 10 Installer ISO for Windows 10 Preparation All the preparation is done in macOS on the Mac that is having an issue booting Windows. It is important to use this Mac since it will be used to identify the correct Windows drivers. USB Flash Drive The USB Flash drive must be formatted as exFAT. • Insert an 8GB or larger flash drive into a USB port on the Mac • In Disk Utility, format the Flash drive as exFAT.

Bootable

Quit Disk Utility after this operation completes. Boot Camp Driver Open Boot Camp Assistant in the Utilities folder, and download the current Windows Support Software from the Action menu. Save the Windows Support Software to your desktop or other location, but do not save directly to the USB Flash Drive.

Windows Install Media Download the current install media from the Microsoft website. Windows is not going to be installed, but the install media will give access to the command line tools in Windows. Select the version of Windows that is closes to the version of Windows installed on the Mac (Windows 8, Windows 10). It does not matter what edition of Windows is used since Windows is not going to be installed. Create Recovery USB Flash Drive To create the USB Flash drive, follow these steps: • Mount the Windows ISO that was downloaded from Microsoft. To mount the ISO, double click on the ISO in the Finder.

• Drag all the files and folders from the mounted ISO to the USB Flash Drive. • Drag the contents of the Windows Support Software to the USB Flash Drive. • If there is not an AutoUnattend.xml at the top level of the drive (as shown below), download, unzip it, and add it to the drive. AutoUnattend.xml provides the location of the $WinPEDriver$ folder to load the drivers during boot. • The 2018 MacBook Air (and potentially Macs after that) have cannot load the IntelMEI driver and give a “Windows Setup could not insatll one or more boot-critical drivers.

To install Windows, make sure that the drivers are valid, and restart the installation”. On the USB Flash drive, open the $WinPEDriver$ and remove the IntelMEI folder. Once the Flash drive has been created, it should look like this: The $WinPEDriver$ folder is important because the $WinPEDriver$ folder contains the drivers for Windows to boot successfully from the USB Flash drive and the hardware on that Mac. Boot from the USB Flash drive To inject the drivers, the Mac must be booted from the USB Flash drive.

• Insert the USB Flash drive into an available USB port on the Mac • Reboot while holding the option key. • Select EFI volume in the startup selector.

If Windows does not boot from the USB Flash drive after showing the Windows logo, you may have to run the following command to tell the firmware to boot the windows installer from the USB flash drive. This has been observed on the late-2014 Mac Mini but may affect other models as well. To set the variable: • by booting to the recovery partition.

• Boot back to macOS and open Terminal. Run the follow command and enter the admin password when prompted: sudo nvram InstallWindowsUEFI=1 Insert the USB flash drive if it is not inserted, reboot, and select the EFI volume from the startup selector. Note the InstallWindowsUEFI variable is cleared at each reboot, so you will to set it again if you do not select the USB Flash Drive.

Command Prompt and Mapped Drives When Windows 10 starts up, it will prompt for installation of Windows 10. To open up a DOS window, press Fn-Shift-F10 (or just shift-F10) or click Repair Computer->Troubleshoot->Command Prompt (if available). Once in the command prompt, there are usually 3 drive letters available: X, C, and D.

• X: This is Windows that you are booted into in memory. The files from the boot.wim on the flash drive are copied to memory and then booted to. • C: Boot Camp partition • D: The USB Flash drive Running Utilities Within the Windows command prompt, you can run utilities on the Boot Camp partition. Pm software for mac.

Excel for mac vlookup not working. Re: Vlookup formula not working i argued the same at mr excel, you need to know 2 extra things,how to enter arrays and when to enter arrays as as a whole range at once. Also if you change your mind you have to delete the whole thing and start again as you cannot edit part. VLOOKUP not working in excel for MAC 2011. Ask Question 1. I have a problem when using VLOOKUP in excel for MAC 2011. I am looking up for a value two column in different sheet, Column A is the one I want to check, Column B is the reference. Large CSV tabbed delimited text files will not open in Excel 2011 or OO on Mac. 2013 - Work, Excel for MAC at home Posts 3. VLookUp across 2 worksheets not working! VLookUp across 2 worksheets not working! Hello JeteMc thank you I will give this a try and if no joy then will upload! Register To Reply. Tags for this Thread. My vlookup is only working for the top half of my spreadsheet and then stops working on any cell past row 270. My vlookup table is a named range, first column in order by dates, returning column is to the left of the reference column and formatting matches and is not text. VLOOKUP on Mac Excel The VLOOKUP function, when mastered, is one of the most useful functions in Microsoft Excel. A VLOOKUP is a function that works off the first column in a list of data.